The Omega DP7600-R is a high-speed, high-resolution 1/8 DIN strain-gauge readout performing 1000 conversions per second at 15-bit-plus-sign resolution, with peak/runout tracking, four limits and single-button tare on a 5-digit red LED. This version is factory-fitted with a dual 2.5 A / 115 Vac Form A relay output for alarm or control.
Specifications per the OMEGA DP-7600 User’s Guide (M2838).
Overview
The Model DP-7600 is a high-speed, high-resolution strain-gauge readout that performs 1000 conversions per second at 15 bits plus sign. Limit checking and peak/runout tracking run at a user-selectable 1 to 500 Hz while the display shows a stable 1 Hz filtered reading. Peak and runout values are available from the front panel, and a tare of up to 50% of span can be captured with a single key press, then enabled or disabled through absolute and relative reading modes. Four limit setpoints drive front-panel LED status, all programming is done from five front-panel switches, and calibration is protected by a security code. Remote interfacing is available over RS-232/RS-485 or active-low logic inputs on the rear.
Best for
- High-speed force, load and strain readout up to 1000 conversions per second
- Peak and runout capture on test stands and presses
- Limit and alarm indication with four independent setpoints
- Single-button tare up to 50% of span with absolute/relative modes
- Alarm or on/off switching via the dual Form A relay output
Key Features
1000 readings/sec
High-speed acquisition at 1000 conversions per second with 15-bit-plus-sign resolution for fast, repeatable force and strain capture.
Peak & runout tracking
Tracks peak and runout at a user-selectable 1 to 500 Hz, displayable from the front panel, while showing a stable 1 Hz filtered reading.
Four limit setpoints
Four limits with front-panel LED status for alarm and pass/fail indication during data acquisition.
Single-button tare
Capture a tare of up to 50% of span with one key press; enable or disable it any time via absolute and relative modes without losing the value.
Front-panel programming
All setup from five front-panel switches, with calibration protected by a security code to prevent accidental changes.
Dual relay output
Factory-fitted dual 2.5 A at 115 Vac Form A relay output for alarm or control switching.
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | Omega DP7600-R |
| Meter type | High-speed strain-gauge readout |
| Display | 5-digit red LED, 1 Hz filtered reading |
| Resolution | 15 bits plus sign |
| Conversion rate | 1000 conversions/sec |
| Limit / peak / runout rate | User-selectable 1 to 500 Hz |
| Input | Strain-gauge bridge; switch-set full-scale sensitivity |
| Tare | Up to 50% of span, single-button; absolute/relative modes |
| Limits | 4 setpoints with front-panel LED status |
| Peak / runout | Tracked and displayable from the front panel |
| Programming | 5 front-panel switches; security-code calibration |
| Serial interface | RS-232 / RS-485 (optional) |
| Relay output | Dual 2.5 A at 115 Vac, Form A |
| Logic inputs | Active-low, rear terminal |
| Analog output | Optional analog-output board |
| Front size | 1/8 DIN |
| Mounting | Panel |
| Power supply | AC |
Documentation
DP-7600 User’s Guide (M2838)Related Products
Frequently Asked Questions
What does the Omega DP7600 measure?
It is a high-speed strain-gauge readout for force, load and strain signals, performing 1000 conversions per second at 15 bits plus sign.
How fast is it?
1000 conversions per second, with limit checking and peak/runout tracking at a user-selectable 1 to 500 Hz; the display shows a stable 1 Hz filtered reading.
Can it capture peak force?
Yes. Peak and runout are tracked and shown from the front panel, and a tare of up to 50% of span can be captured with a single key press.
What is the -R relay output rated for?
The -R adds a dual 2.5 A at 115 Vac Form A relay output for alarm or control switching.
How is the DP7600 programmed?
All setup is done from five front-panel switches; calibration is protected by a security code to prevent accidental changes.
- Series:
- DP7600
- Meter Type:
- Strain Gauge Readout
- DIN Size:
- 1/8 DIN
- Display:
- 5-Digit Red LED
- Power Supply:
- AC
- Relay Outputs:
- 2
- Analog Output:
- Optional
- Communication:
- RS-232/RS-485 (optional)
