The ACI A/GP M20' HARNESS is a 20 ft (6.10 m) Packard 3-pin wire harness for ACI GP Series and A/GP-N4 NEMA 4 gage pressure transducers. The A/GP M20' HARNESS uses metal-clad cable for added physical protection and abrasion resistance in industrial or exposed runs, and terminates in a mating Packard 3-pin connector that plugs directly into the transducer.
Wire color coding follows the ACI GP wiring convention: Red is the power lead (to supply +), White is the return lead (to controller 4-20 mA analog input +), and a shield drain wire connects to earth ground. A black wire is included but is not used in 4-20 mA service.
Warranty
LIMITED
WARRANTY
Manufacturer-backed coverage. ACI accessories carry a Two (2) Year Limited Warranty. ZOT Supply is an authorized ACI distributor; the A/GP M20' HARNESS ships factory-new with full manufacturer warranty intact. Full terms appear in the front of ACI’s Sensors & Transmitters catalog and at workaci.com.
Key Features
Mating Packard 3-Pin Connector
Industry-standard Packard connector mates directly with the ACI GP / A/GP-N4 transducer body for a clean, vibration-resistant electrical connection. No additional adapters required.
20 ft (6.10 m) Metal-Clad Cable
Pre-terminated 20 ft (6.10 m) cable in a metal jacket. Metal-clad armor protects against physical damage in industrial environments.
Color-Coded Conductors
Standard ACI color coding: Red (Power), White (Return / 4-20 mA signal), shield drain wire (earth ground). Black wire included but not used in 4-20 mA service.
Sized for Common Installations
Available lengths from 2 ft up to 40 ft (plenum) and 10 ft / 20 ft (metal-clad). Pick the length that matches the run from your transducer location back to the panel.
Technical Specifications
| Specification | Value |
|---|---|
| Model | A/GP M20' HARNESS |
| ACI Item Number | 147881 |
| Product Type | Packard 3-Pin Wire Harness |
| Cable Length | 20 ft (6.10 m) |
| Cable Type | Metal-Clad |
| Connector | Packard 3-Pin (mates with ACI GP / A/GP-N4 transducer) |
| Conductors | Red (Power), White (Return), Black (not used in 4-20 mA), Shield (earth ground) |
| Compatible Transducers | All ACI GP Series and A/GP-N4 Series Gage Pressure Transducers |
| Installation Use | General indoor and industrial installations; provides added physical protection |
| Warranty | 2-Year Limited |
| Manufacturer Part Number | A/GP M20' HARNESS |
Compatible Transducers
ACI GP Series — base transducers (Packard connector)Documentation
Frequently Asked Questions
What is the A/GP M20' HARNESS used for?
The A/GP M20' HARNESS is the cable harness that connects an ACI GP Series or A/GP-N4 NEMA 4 gage pressure transducer to your controller, PLC or data-acquisition system. ACI ships GP transducers with a Packard 3-pin connector only; the wire harness is sold separately so you can choose the length and cable type that matches your installation.
How long is the cable?
The A/GP M20' HARNESS is 20 ft (6.10 m) long, with a Packard 3-pin connector on the transducer end and tinned conductors on the controller end for direct wiring into a screw terminal.
Which transducers is the A/GP M20' HARNESS compatible with?
All ACI GP Series gage pressure transducers (model numbers beginning with GP(0-...) and ending in -P) and the NEMA 4 variants (A/GP(0-...)-20-P-N4). The Packard connector is standardized across the entire GP family.
How is it wired?
Connect Red to the plus terminal of the 13-30 VDC supply, White to the controller’s 4-20 mA analog input (+), Common (-) of the controller to the supply minus, and the shield drain wire to earth ground. The black wire is not used in 4-20 mA service.
Is the A/GP M20' HARNESS plenum rated?
No — the A/GP M20' HARNESS is metal-clad, designed for added physical protection in industrial and exposed runs rather than plenum installation. For plenum service, use the plenum-rated A/GP harnesses (no ‘M’ in the model number).
- Product Type:
- Wire Harness
- Cable Length:
- 20 ft
- Cable Type:
- Metal-Clad
- Connector:
- Packard 3-Pin
- Compatible With:
- ACI GP Series
