The BAPI BA/1K[3W]-I-8"-SS-BB2O is an immersion temperature sensor with a 1000 Ohm Platinum RTD (385 Curve) (3-Wire RTD Configuration (lead-resistance compensation)) sensing element, potted in a 8 inch (203 mm) long, 0.25 inch OD 304 stainless steel probe with thermally-conductive compound. The probe threads into a thermowell via a Stainless Steel double-threaded fitting; on hand-tightening the probe slides up to 1.6 inch inside the enclosure body so the tip seats firmly against the thermowell bottom, giving solid thermal contact regardless of thermowell depth tolerance.
The sensor outputs resistance directly to the BAS analog input (no powered signal conditioning). The BAS converts resistance to temperature using a sensor-specific R/T table programmed in the controller. The unit is housed in the BAPI-Box 2 (Outside Mount) enclosure (NEMA 4 / IP66, UV-Resistant Polycarbonate, UL94 V-0) and wired for Flying Leads. The Outside-Mount (O) configuration orients the mounting flange on the OUTSIDE of the enclosure body, which suits applications where the enclosure must be flush against a panel or wall and the probe exits from the rear. Made in USA by BAPI of Gays Mills, Wisconsin.
Water-pipe, hydronic-loop, cooling-tower-sump, and tank temperature measurement on BAS systems that accept resistance-input directly (1000 Ohm Platinum RTD (385 Curve) (3-Wire RTD Configuration (lead-resistance compensation))). The 8 inch (203 mm) probe fits a matching BAPI thermowell of the same length; for a typical 8 inch insulated pipe, a 4 inch probe in a 4 inch thermowell reaches the centerline (best-case thermal contact with the flowing media).
Key Features
1000 Ohm Platinum RTD (385 Curve) (3-Wire RTD Configuration (lead-resistance compensation)) potted inside a 0.25 inch OD 304 stainless steel probe with thermally-conductive compound. Etched Teflon leadwire is plenum-rated. The double encapsulation keeps the sensor watertight under 100% RH non-condensing service.
Three-wire connection compensates for lead-resistance error on long cable runs (recommended for runs over 100 feet). The third wire lets the BAS measure and subtract the lead-wire resistance from the reading.
1/2 inch NPT stainless steel threads provide a metal-to-metal seal and resist corrosion in process fluids. Use thread sealant per the application.
UV-Resistant Polycarbonate, UL94 V-0. Compact NEMA 4 polycarbonate enclosure with smaller footprint than BB.
Mounting flange located on the OUTSIDE of the enclosure body - the probe exits from the rear and the enclosure mounts flush to a panel or wall. Useful in tight wiring closets and slim-profile installations.
Designed and manufactured by Building Automation Products, Inc. at 750 North Royal Avenue, Gays Mills, Wisconsin. RoHS / CE compliant.
Technical Specifications
| Specification | Value |
|---|---|
| Manufacturer | Building Automation Products, Inc. (BAPI) |
| Manufacturer Part Number | BA/1K[3W]-I-8"-SS-BB2O |
| Series | BAPI Immersion w/ Stainless Steel Fitting |
| Sensor Type | Passive Resistance Sensor (unpowered) |
| Temperature Element | 1000 Ohm Platinum RTD (385 Curve) (3-Wire RTD Configuration (lead-resistance compensation)) |
| Nominal Resistance | 1000 Ohm at 0 degC |
| Sensitivity | 3.85 Ohm/degC (385 curve, DIN43760) |
| Output Type | Resistance (to controller analog input, no polarity) |
| Probe Length | 8 inch (203 mm) |
| Probe Material | 304 Stainless Steel, 0.25 inch outer diameter |
| Probe Construction | Double-encapsulated sensing element with thermally-conductive potting |
| Process Fitting | 1/2 inch NPT Stainless Steel |
| Lead Wire | 22 AWG Stranded, Etched Teflon, Plenum Rated |
| Wiring Option | Flying Leads |
| Enclosure Model | BAPI-Box 2 (Outside Mount) |
| Enclosure Rating | NEMA 4 / IP66 |
| Enclosure Material | UV-Resistant Polycarbonate, UL94 V-0 |
| Enclosure Dimensions (H x W x D) | 4.9 x 2.8 x 2.35 inch (125 x 71.6 x 60 mm) |
| Enclosure Ambient Temperature | -40 to 185 degF (-40 to 85 degC) |
| Ambient Humidity | 0 to 100% RH, non-condensing |
| Mounting Method | Thermowell insertion (1/2 inch NPT Stainless Steel, hand-tightened) |
| Mount Configuration | Outside-Mount (mounting flange on exterior of enclosure) |
| Agency Compliance | RoHS, CE (where applicable) |
| Country of Origin | Made in USA (Gays Mills, WI) |
Documentation
Frequently Asked Questions
BAPI strongly recommends installing this sensor inside a matching thermowell rather than direct-immersion. A thermowell lets the sensor be removed and serviced without draining or depressurizing the pipe / tank, and protects the probe from corrosion or mechanical damage. Match the thermowell length to the probe length (8 inch (203 mm)).
This sensor is a passive 1000 Ohm Platinum RTD (385 Curve) (3-Wire RTD Configuration (lead-resistance compensation)). The BAS controller needs the matching R/T (resistance / temperature) curve programmed in its analog-input setup - typically selectable by manufacturer-specific table name. The full R/T table is at bapihvac.com under Resources -> Sensor Specs.
This SKU uses the BAPI-Box 2 (Outside Mount) (NEMA 4 / IP66, UV-Resistant Polycarbonate, UL94 V-0). Compact NEMA 4 polycarbonate enclosure with smaller footprint than BB.
The SS fitting is double-threaded and seals metal-to-metal with the thermowell - more robust than the nylon NPSM fitting for high-pressure water service or applications where chemical compatibility, vibration, or mechanical abuse could fatigue a plastic fitting. The SS variant uses 1/2 inch NPT threads (standard tapered) which seat with thread sealant; the nylon variant uses 1/2 inch NPSM (straight) threads and is hand-tight only with no sealant.
The mounting flange is relocated to the OUTSIDE of the enclosure body (instead of the standard inside-mount configuration). The probe exits from the rear of the enclosure and the enclosure mounts flush against a panel or wall. Useful in tight wiring closets, slim panel installations, or applications where the enclosure must be flush with the mounting surface.
Yes. BAPI Immersion sensors and transmitters are designed and manufactured by Building Automation Products, Inc. at 750 North Royal Avenue, Gays Mills, Wisconsin (USA).
- Brand:
- BAPI
- Series:
- Immersion SS Double-Threaded Sensor
- Sensor Type:
- Passive Resistance Sensor
- Temperature Element:
- 1000 Ohm Platinum RTD (385 Curve)
- Output Signal:
- Resistance (to BAS analog input)
- Probe Length:
- 8 inch (203 mm)
- Probe Fitting:
- Stainless Steel (1/2 inch NPT, Double-Threaded)
- Calibrated Range:
- -40 to 221 degF (probe operating range, passive)
- Enclosure:
- BAPI-Box 2
- Mount Position:
- Outside Mount
- Enclosure Rating:
- NEMA 4 / IP66
- Wiring Configuration:
- Flying Leads
- Country of Origin:
- Made in USA